Кровать Incanto Gio 9 в 1 венге--> Настенная--> Платформа CRS CISCO CRS-16-KP-REAR

Платформа CRS CISCO CRS-16-KP-REAR


Reviewed by:
Rating:
5
On 14.04.2019

Summary:

.

Платформа CRS CISCO CRS-16-KP-REAR



Обзор:

Space CRS 17 Set To Music. Платформа CRS CISCO CRS-16-KP-REAR

The Cisco CRS Series enhanced 16-slot line card chassis is shipped with exterior cosmetic components for the front PLIM side and rear MSC side of the chassis.
Note Some exterior cosmetic components, such as the cable pass-through accessory plates, are not required to be installed.
This figure shows the default exterior cosmetic components for the front PLIM side of a Cisco CRS Series enhanced 16-slot line card chassis.
Default Front PLIM Side Exterior Cosmetic Components 1 Upper grille support 5 Doors 2 Unistruts 6 Upper grille 3 Bracket for lower grille 7 Vertical cable troughs 4 Lower grille This figure shows the exterior cosmetic components for the front PLIM side of a Cisco CRS Series enhanced 16-slot line card chassis installed as part of a wide duct system.
Front PLIM Side Exterior Cosmetic Components—Wide Duct System 1 Upper grille support 5 Doors 2 Unistruts 6 Upper grille 3 Bracket for lower grille 7 Wide vertical cable troughs 4 Lower grille This figure shows the exterior cosmetic components for the rear MSC side of a Cisco CRS Series enhanced 16-slot line card chassis.
Rear MSC Side Exterior Cosmetic Components 1 Vertical cable trough 4 Doors 2 Bracket for optional rear kick panel 5 Upper air grille 3 Rear kick panel optional, orderable separately Installing the Front PLIM Side Exterior Cosmetic Components This section describes how to install the default front PLIM side exterior cosmetic components on the Cisco CRS Series enhanced 16-slot line card chassis.
Note While it is possible to install the various exterior components on the Cisco CRS Series enhanced 16-slot line card chassis in a different order, it is easier to install them in the order outlined in this section.
The lower grille screen and frame assembly are shipped pre-installed in the chassis.
The upper grille support is not shipped pre-installed on the chassis but must be installed before the power shelves are installed in the chassis.
See the Cisco CRS Carrier Routing System 16-Slot Line Card Chassis Unpacking, Moving, and Securing Guide.
The upper grille support should already be installed at the top of the chassis.
See the for more information.
Unpack all cosmetic parts to prepare for installation.
Installing the Cable Pass-through 4 Plates Optional —Default Cable Trough Only Remove the blank plates by unscrewing the four screws on each one.
Attach the inner cut-out plates using the four screws provided.
See the Cut-Out Plates figure.
Attach the outer cut-out plate using the four screws provided.
Attaching the Optional Wide Front Vertical Cable Troughs Optional Trough.
Attach the vertical cable troughs—one right and one left—to the front PLIM side of the chassis see Installing the Front Vertical Cable Troughs above : 7.
Installing the Upper Grille Attach the upper grille by carefully inserting the four tabs on the grille into the appropriate hook hanger brackets on the top of the upper grille support see below figure.
Press the grille and bezel firmly against the chassis until it snaps onto the ball stud snaps.
Attaching the Lower Grille Attach the lower grille by carefully inserting the tabs on the grille into the brackets on the bottom of the inlet grille frame.
Press the lower grille firmly until it snaps onto the ball stud snaps.
Attaching the Front Exterior Doors Orient the doors so that the slot on the metal part in the middle of the doors is lined up with the tab on the vertical cable trough.
The door will then drop into продолжение здесь />See the below figure.
Insert the screws into the appropriate screw holes in the doors, and use the screwdriver to tighten fully.
There are 11 M4x8 screws on each side for the metal sections of the doors and six M4x8 screws on each side for the plexiglass section of the door.
Ensure that the doors are properly aligned.
For wide duct installations see Door Adjustments for Wide Trough Installation figure below : DETAILED STEPS Step 1 Unpack all cosmetic parts to prepare for installation.
Step 2 Attaching the Default Front Vertical Cable Troughs Attach the vertical cable troughs—one right and one left—to the front 4 side of the chassis see Installing детальнее на этой странице Front Vertical Cable Troughs figure below : Note The part number for the right side vertical cable trough is 800—35625—xx; the part number for the left side vertical cable trough is 800—35644—xx.
Installing the Front Vertical Cable Troughs This Image 209820.
Note Depending on the size of the installation and the number and type 4 cables being used, the body of the chassis may become overcrowded and unable to accommodate all the required cables.
To resolve this issue, you can install two pass-through accessory plates to allow cables be guided outside the default vertical troughs.
Step 4 Attach the inner cut-out plates using the four screws provided.
See the Cut-Out Plates figure.
Cut-Out Plates Step 5 Attach the outer cut-out plate using the four screws provided.
Step 6 Attaching the Optional Wide Front Vertical Cable Troughs Optional Trough.
Attach the vertical cable troughs—one right and one left—to the front PLIM side of the chassis see Installing the Front Vertical Cable Troughs above : Note The part 4 for the right side vertical cable trough is 800—36457—xx; the part number for the left side vertical cable trough is 800—36456—xx.
See the below figure.
Use the screwdriver to turn the screws clockwise to attach the cable trough brackets firmly to the side of the chassis.
See the below figure.
Note The brackets for securing the wide cable trough to the side of the chassis are shipped pre-installed on the cable trough.
Attaching Wide Vertical Cable Trough Brackets 4 Side of Chassis Step 7 Installing the Upper Grille Attach the upper grille by carefully inserting the four tabs on the grille into the appropriate hook hanger brackets on the top of the upper grille support see below figure.
Step 8 Press the grille and bezel firmly against the chassis until it snaps onto the ball stud snaps.
Attaching the Front Upper Grille Step 9 Attaching the Lower Grille Attach the lower grille by carefully inserting the tabs on the grille into the brackets on the bottom of the inlet grille frame.
Step 10 Press the lower grille firmly until it snaps onto the ball stud snaps.
Installing the Front Lower Grille 1 Front lower grille Note The procedure for installing the front doors on the default vertical cable troughs and the wide cable troughs is the same.
Step 11 Attaching the Front Exterior Doors Orient the doors so that the slot on the metal part in the middle of the doors is lined up with the tab on the vertical cable trough.
The door will then drop into position.
See the below figure.
Note The part number for the right door is 800—35628-xx; the part number for the left door is 800—35646-xx.
The door lock is on the left door.
Caution The doors scratch easily, so they should be handled with care.
Attaching the Front Doors 1 Screw locations Step 12 Insert the screws into the appropriate screw holes in the doors, and как сообщается здесь the screwdriver to tighten fully.
There are 11 M4x8 screws on each side for the metal sections of the doors and six 4 screws on each side for the plexiglass section of the door.
Note To ensure that the door is well supported during installation, insert screws in the upper and lower metal sections first.
Step 13 Ensure that the doors are properly aligned.
The following substeps apply to the default cosmetics.
Note Typically, the doors will close without interfering with each other.
However, you may need to adjust either the left or right door, or both, to align the doors properly.
Adjust doors only if necessary.
Using the 2 mm hex key wrench, tighten the bottom set screws one full turn.
Snug the screws that attach the vertical trough to the chassis and check the door alignment.
Using the 2 mm hex key wrench, tighten the top set screws one full turn.
Snug the screws that attach the vertical trough to the chassis and check the door alignment.
Note Typically, the doors will close without interfering with each other.
However, you may need to adjust either the left or right door, or both, to align the doors properly.
Adjust doors only if necessary.
Door Adjustments for Wide Trough Installation 1 Minor adjustments 11 screws 3 Major adjustments 7 screws on the vertical metal bar on each door 2 Screwdriver location Installing the Rear MSC Side Cosmetic Components This section describes how to install the rear MSC side exterior cosmetic components on the Cisco CRS Series enhanced 16-slot line card chassis.
While it is possible to install the various exterior components on the chassis in a different order, it is easier to install them in the order outlined in this section.
The midchassis cable management bracket and rear door strike tube are shipped pre-installed on the chassis.
See Cisco CRS Carrier Routing System 16-Slot Line Card Chassis Unpacking, Moving, and Securing Guide.
Unpack all cosmetic parts to prepare for 4 />Attaching the Rear Vertical Cable Troughs Before you attach the left and right vertical cable troughs, if the verticals h ave L-brackets, they will need to be removed so that they do not interfere with the air deflector.
Attach the rear vertical cable troughs—one left and one right—to the rear of the chassis see the figure below by inserting the 10 M4x14-mm pan head screws five on each side and using the screwdriver to turn the screws clockwise to attach the cable troughs firmly to the chassis.
You might need to use a ladder to reach the upper screws.
Attaching the Upper Rear Air Grille Follow these steps if you are using the vertical troughs.
To install the upper rear air grille without the vertical troughs, see the.
Attach the upper grille by carefully hooking the hanger brackets that are on top of the grille over the hook supports that are on top of the vertical cable troughs see below figure.
Press the upper rear air grille firmly until its ball studs snap onto the ball stud retainers.
Attaching the Rear Kick Plate Carefully slot the tabs on the bottom of the rear kick plate into the brackets on the chassis see below figure.
To secure the top fasteners, firmly press the top edge of the rear kick plate against the chassis until it snaps onto the ball stud snaps.
Installing the Rear Doors Orient the doors so that the slot on the metal part in the middle of the doors is lined up with the tab on the vertical cable trough.
The door will then drop into position.
Insert the screws into the appropriate screw holes in the doors, and use the screwdriver to tighten fully.
There are 10 M4x8 screws on each side for the metal sections of the doors and six M4x8 screws on each side for the plexiglass section of the door.
Ensure that the doors are properly aligned.
DETAILED STEPS Step 1 Unpack all cosmetic parts to prepare for installation.
Step 2 Attaching the Rear Vertical Cable Troughs Before you attach the left and right vertical cable troughs, if the verticals h ave L-brackets, they will need to be removed so that they do not interfere with the air deflector.
Removing L-Brackets Step 3 Attach the rear vertical cable troughs—one left and one right—to the rear of the chassis see the figure https://prognozadvisor.ru/nastennaya/nastennie-chasi-salvador-dali-50-h-50-sm.html by inserting the 10 M4x14-mm pan head screws five on each side and using the screwdriver to turn the screws clockwise to attach the cable troughs firmly to the chassis.
You might need to use a ladder to reach the upper screws.
Note We recommend that you use two people to install the troughs, one person to hold the troughs in place while the other person inserts and tightens Lebel - Охлаждающий аромашампунь для жирной кожи 1000 мл screws.
Attaching the Rear MSC Side Vertical Cable Troughs Step 4 Attaching the Upper Rear Air Grille Follow these steps if you are using the vertical troughs.
To install the upper rear air grille without the vertical troughs, see the.
Attach the upper grille by carefully hooking the hanger brackets that are on top of the grille over the hook supports that are on top of the vertical cable troughs see below figure.
Note Because the upper rear air grille must be installed at the top of the chassis, it is easier to stand on a ladder while installing it.
Note Ensure cables are dressed correctly to ensure enough clearance to install the детальнее на этой странице air grille.
Step 5 Press the upper rear air grille firmly until its ball studs snap onto the ball stud retainers.
Step 6 Attaching the Rear Kick Plate Carefully slot the tabs on the bottom of the rear kick plate into the brackets on the chassis see below figure.
Attaching the Rear Kick Plate 1 Rear kick plate Step 7 To secure the top fasteners, firmly press the top edge of the rear kick plate against the chassis until it snaps onto the ball stud snaps.
Step 8 Installing the Rear Doors Orient the doors so that the slot on the metal part in the middle of the doors is lined up with Видеокамера AHD/TVI/CVI/CVBS Giraffe Чайник Leben 291-067 v3(2.8) tab on the vertical cable trough.
The door will then drop into position.
Note The part number for the right door is 800—35638—xx; the part number for the left door is 800—35475-xx.
The door lock is on the left door.
Caution The doors scratch easily, so they should be handled with care.
Attaching the Rear Doors Step 9 Insert the screws into the appropriate screw holes in the doors, and use the screwdriver to tighten fully.
There are 10 M4x8 screws on each side for the metal sections of the doors and six M4x8 https://prognozadvisor.ru/nastennaya/nastennaya-split-sistema-pioneer-kfr25mw-kor25mw.html on each side for the plexiglass section of the door.
читать статью To ensure that the door is well supported during installation, insert screws in the upper and lower metal sections first.
Step 10 Ensure that the doors are properly aligned.
Note Typically, the doors will close without interfering with each other.
However, you may need to adjust either the left or right door, or both, to align the doors properly.
Adjust doors only if necessary.
Using the 2 mm hex key wrench, tighten the bottom set screws one full turn.
Snug the screws that attach the vertical trough to the chassis and check the door alignment.
Using the 2 mm hex key wrench, tighten the top set screws one full turn.
Snug the screws that attach the vertical trough to the chassis and check the door alignment.
Attaching the Upper Rear Air Grille and Rear Kick Plate Without Vertical Troughs Use the procedures in this section to install the upper rear air grille CRS-16-REAR-GRL and rear kick 4 CRS-16-KP-REAR if you are not using the vertical troughs.
If you are using the vertical troughs, see the procedure in the.
Note Because the upper rear air grille must be installed at the top of the chassis, it is easier to stand on a ladder while installing it.
Note Ensure cables are dressed correctly to ensure enough clearance to install the upper air grille.
To attach the upper rear air grille, hang the grille on the inside grille supports.
Pivot to the closed position.
To attach the rear kick plate, first attach the two brackets provided with the kick plate and fasten them using the captive screws that are included see figure below.
Carefully slot the tabs on the bottom of the rear kick plate into the brackets on the chassis see figure below.
To secure the top fasteners, firmly press the top edge of the rear kick plate against the chassis until it snaps onto the ball stud snaps.
DETAILED STEPS Step 1 To attach the upper rear air grille, hang the grille on the inside grille supports.
Grille Positioning and Inside Supports Step 2 Pivot to the closed position.
Step 3 To attach the rear kick plate, first attach the two brackets provided with the kick plate and fasten them using the captive screws that are included see figure below.
Attaching Brackets for the Rear Kick Plate 1 Brackets for rear kick plate Step 4 Carefully slot the tabs on the bottom of the rear kick plate into the brackets on the chassis see figure below.
Attaching the Lower Rear Kick Plate 1 Rear kick plate Step 5 To secure the top fasteners, firmly press the top edge of the rear kick plate against the chassis until it snaps onto the ball stud snaps.

Комментарии 8

Добавить комментарий

Ваш e-mail не будет опубликован. Обязательные поля помечены *